Krytac Technical Discussion Forum
Sign up Calendar Latest Topics
 
 
 


Reply
  Author   Comment   Page 1 of 2      1   2   Next
Hardknox

Junior Member
Registered:
Posts: 18
Reply with quote  #1 
With more and more people receiving their Vectors, I figured this would be the number 1 question after taking ownership. I Finally received my vector, and tried out some batteries to see what the biggest and best fit LiPos would fit.
So with that said, here is a list of batteries that I know fit. Some you have to change to deans connectors because the tamiya connectors are just to big (long) once paired, to fit in the battery compartment.

https://www.evike.com/products/56186/ ....... Matrix 11.1v 1400Mah (candy bar size) LiPo [must change to deans in order to fit]

https://www.evike.com/products/40190/ ...... Tenergy 11.1v 1000Mah (stick type) LiPo
0
dante_vietro12

Regular Member
Registered:
Posts: 64
Reply with quote  #2 
Valken 11.1 1000 mah lipo fits once wired to deans
0
StayedSpark

Junior Member
Registered:
Posts: 2
Reply with quote  #3 
the VP racing 11.1v 1300 mAh 25c stick battery fits in my vector pretty much perfectly tbh [biggrin]

http://www.patrolbase.co.uk/lipo-and-life-airsoft-batteries/vp-racing-battery-11-1v-1300-mah-stick-battery.htm#.WaacWcaVthE
0
Arsonick14

Junior Member
Registered:
Posts: 2
Reply with quote  #4 
Quote:
Originally Posted by dante_vietro12
Valken 11.1 1000 mah lipo fits once wired to deans


The one I have fits without change to deans.

Valken Energy LiPo 11.1v 1000mAh Battery https://www.amazon.com/dp/B00N4L2910/ref=cm_sw_r_other_apa_qNAVzbEA5RBD4
0
Fenrirwolf

Avatar / Picture

Junior Member
Registered:
Posts: 14
Reply with quote  #5 
Now as my Vector is here too, i try to figure out which battery would fit.
As 1000mAh is really low, i was wondering if this one might would fit? https://hobbyking.com/en_us/turnigy-1800mah-3s-20c-lipoly-pack-w-ec3-e-flite-compatible-eflb32003s.html?___store=en_us
0
Guges Mk3

Avatar / Picture

Regular Member
Registered:
Posts: 256
Reply with quote  #6 
Create a model of your battery compartment with cardboard stacks, then measure and compare to the specs of the pack, with wire of course to the model and compare.

Pack Size: 108 x 36 x 20mm

In addition you should get a pack that can deliver 20A of continuous discharge power (C * Mah).  If it can't, its not a good pack.
0
Fenrirwolf

Avatar / Picture

Junior Member
Registered:
Posts: 14
Reply with quote  #7 
I've just measured the compartment. If the Deans plug shall fit aside, it should not be bigger than: 11cm x 2,1cm x 2,4cm.

Sadly that pretty small. Hard to find Batteries bigger than 1100mAh.
  
0
Guges Mk3

Avatar / Picture

Regular Member
Registered:
Posts: 256
Reply with quote  #8 
Do you have to run a 3s?
0
Fenrirwolf

Avatar / Picture

Junior Member
Registered:
Posts: 14
Reply with quote  #9 

If you are happy with a crappy slow 7.4V, then sure you can run them [wink]

But as my other Guns run with 11.1V and Gate Titans with low ratio gears, for me the triggerresponse of the Vector is already pretty slow, even with 11.1V.

0
Guges Mk3

Avatar / Picture

Regular Member
Registered:
Posts: 256
Reply with quote  #10 
My 2S packs are not "crappy" or "slow" and is far better performing than Most batts peddled by Valken, Tenergy and others that are not suitable for Airsoft use.

I have an AEG that runs off a 2S and gets 25rps on standard ratio gears at 398fps.  Granted the motor is "not" stock.

But, with that...I will have a 3S 1400mah pack available in about 4 weeks that should just fit in that space you listed.  Under load it is a 35A pack with a burst capability of 70A.  Fully charger its rather high at ~4.34V per cell.
0
xMONSTER

Junior Member
Registered:
Posts: 3
Reply with quote  #11 
https://www.evike.com/products/56186/

Would this work? The dimensions are
95mm x 31mm x 17mm
0
dhong_sd

Junior Member
Registered:
Posts: 41
Reply with quote  #12 
@xMONSTER. It will not fit. You might not be able to put the wires on the side. Ive tried every battery in evike that could fit unfortunately the only one that can fit is the tenergy 1000mah 11.1 or the 7.4v. I just have a spare just in case i run out of juice in the field. I know the struggle man. Hope this can help.
0
xMONSTER

Junior Member
Registered:
Posts: 3
Reply with quote  #13 
Too bad that VPairsoft 11.1v 1300Mah isnt sold in America its seems to help the sloppy trigger response and stops the gears from not completing a full cycle or the 25C output atleast helps
0
xMONSTER

Junior Member
Registered:
Posts: 3
Reply with quote  #14 
Also does anyone have the battery housing size with the cables in it?
0
kinesis

Regular Member
Registered:
Posts: 100
Reply with quote  #15 
get a pack(s) from Guges MK3. i measured mine out and he found me a battery to fit.

i have 3 from him. 2 that are 3s and 1 that is 2s.

there should be a link in the forum with pics showing the fit.

the 3S is 1400mah. my vector gets about 23-25 rof on this battery. and it is good for about 30-35 magazines. for me anyways. i am semi only. the fields we have here aren't full auto friendly. but more to the point the group i play with are friendly people and we don't really full auto each other.


-k
0
Previous Topic | Next Topic
Print
Reply

Quick Navigation:

Easily create a Forum Website with Website Toolbox.