Krytac Technical Discussion Forum
Sign up Calendar Latest Topics
 
 
 


Reply
  Author   Comment   Page 6 of 10     «   Prev   3   4   5   6   7   8   9   Next   »
Allizard

Avatar / Picture

Chief Janitor
Registered:
Posts: 846
Reply with quote  #76 
Like I said, G&P mag is a bit oversize.  Just like their gun's magwell is oversize.

0
dillingeruk

Junior Member
Registered:
Posts: 7
Reply with quote  #77 
ares amoeba m4 high caps( not ares m4/m16 mag) with the built in magpul work really well. good feed and tight fit. no wobble.

also the ics m4 mags that come with the cxp range work.
0
digital8

Junior Member
Registered:
Posts: 9
Reply with quote  #78 
Ares Amoeba 300rds High Cap magazines.

Ares-amoeba-hi-cap.jpg 

Bought three of these but none of them feed well in my Krytac CRB.

Pro's.:
- Look and feel great
- Very nice fit, no wobble at al
- Maggpull works great

Cons.:
- Bought three of these mag's but none of them feed well using a 7.4v 15C LiPo, only solution is to pull the mag and reinsert it
- The winding wheel is difficult to use because it's so small and only sticks out a tiny bit on the bottom of the mag and i wasn't even using gloves.
- The opening to insert BB's is not a sliding door but a door that opens upwards so if you drop the mag (i tried this by dropping it from 2 meters high) the door can jump open spilling your BB's.



After more testing with these Amoebe magazines, i have to adjust my findings.

Most importantly the magazines do feed great (i put over 2000 BB through the 3 magazines to test them), they feed just about every BB, the problem is not a feeding issue the problem with these magazines is winding them this is wy i thought they where not feeding correctly, as stated above it is very difficult to wind these magazines, the bottom of the magazine is engrossed so the wheel sticks out only a little (look at the picture posted below), the only way to fully wind the magazine is by first using your finger an then using your nail, so winding them with gloves on is almost impossible.


ares-amoeba-m4-highcap-300rds-tan.jpg 



0
Anttwan

Junior Member
Registered:
Posts: 2
Reply with quote  #79 
just got a box of hexmag's there alittle wobble in them. They feed ok but if you put all 120 bb's in my CRB at least it feed 2 or 3 bbs some time but 80% of the time they feed really good.. i could be the bb's im using which are .25 krytac's. im goin to try some .28 when they get here.
0
nockeer

Avatar / Picture

Junior Member
Registered:
Posts: 2
Reply with quote  #80 
Amoeba Mid-Cap 140 rnds fit very well - there is little shake, but thanks to this you can make quick mag change. It feed well, even latest balls.
0
Magic Mike Airsoft

Avatar / Picture

Junior Member
Registered:
Posts: 3
Reply with quote  #81 
The Angel Custom 1500 Round Firestorm Drum Flashmag has been working just fine for me. Looks pretty sweet as well. Gonna make a review video for it soon!
0
MarkMarkington

Junior Member
Registered:
Posts: 13
Reply with quote  #82 
I used a friends ares 140rd mid cap and ended up buying 5 that weekend. They work so well, feed great, nice and solid and the texturing / magpul isn't half bad at less than £10 a mag
0
otang

Junior Member
Registered:
Posts: 1
Reply with quote  #83 
I have magpul PTS 120 round PMAGS mids and they don't feed well. Sometimes they feed 1/2 the the shots, and other times they feed about 3/4 of the shots. They have worked well on other replicas and I do maintenance on them including slight stretching of the springs.
0
wchiang77

Junior Member
Registered:
Posts: 6
Reply with quote  #84 
I use SocomGear Lancer Tactical L5 190rds midcap with no issues, just the locking on the mag retention seems a little sketchy but so far no missfeeds.
0
abrmleon

Junior Member
Registered:
Posts: 8
Reply with quote  #85 

Hexmags doesnt work, feeding problems.

K120 trhow all bb's withoth problems, 20 rounds per second without problems


11.1 Lipo 25C

guarder SP170 Spring

on Krytac SPR

0
whiplash

Junior Member
Registered:
Posts: 19
Reply with quote  #86 
Just got my new FG mk2 SPR, but all my k 120 mags feed teriable, and the mag drops out of the gun half way through the mag. This happens with all my mags, but not the high cap it came with !
0
creamycoconut

Junior Member
Registered:
Posts: 1
Reply with quote  #87 
Dytac Invader 120 rd polymer midcaps feed well so far
0
EthanBourgeois

Junior Member
Registered:
Posts: 5
Reply with quote  #88 
Kwa k120 mid cap mags feed pretty well.
0
TimmyHorton

Avatar / Picture

Junior Member
Registered:
Posts: 15
Reply with quote  #89 
Just ran the Evike 190rd B.A.M.F mags at Op:34 they feed great and fit well with just enough play to allow easy insertion and free fall when the mag catch is pressed, 
However I did find that if you stuff them all the way up to 190 rounds that the first 10 shots out of a newly inserted mag will not be hoped and will only shoot out 20 feet, This is however is not a problem with either the mags or the CRB it is simply user error and is easily fixed by only loading in around 170rds instead of 190 to relieve some of the spring tension.
0
delbs

Junior Member
Registered:
Posts: 9
Reply with quote  #90 
Having issues with KW(A) 120s in the SPR MK2. They seem to wobble side to side and also have up and down play in them. In some cases, the mag is able to fall out. Was there a change in the mag well design from the original trident to the MK2? My original trident has 0 issues and the mags fit amazingly! There's no play yet they come out easily when you release them. I posted a video on the Krytac facebook about the issue I'm having on the poll about magazines. Was looking for some more info on the mag well size change possibly or if I got a wonky gun. [frown] Any help or info would be nice. Here's the FB link:

https://www.facebook.com/groups/1467661306839919/permalink/1750770605195653/?comment_id=1781848265421220&reply_comment_id=1781858868753493&notif_t=group_comment&notif_id=1475799429484089
0
Previous Topic | Next Topic
Print
Reply

Quick Navigation:

Easily create a Forum Website with Website Toolbox.