Registered: 1421200466 Posts: 1
Reply with quote #1
I have a bone stock CRB but hate the A2 motor grip because of the nub at the front. I've tried to use my old G&G grip but it places the motor too high even when I adjust the motor height to the lowest. What are some grips that are compatible with the stock motor that don't have the finger nub i.e. MOE/Umbrella Corps. Thanks
Registered: 1409537746 Posts: 116
Reply with quote #2
I use the Magpul Black AEG grip. I love the feel, and it is larger; not as skinny as the stock one. Required a bit of grinding on the inside of the plate so that the motor sits lower and can be adjusted properly
Registered: 1416510762 Posts: 14
Reply with quote #3
I use that Umbrella Corp (23 grip one), fits great, no problems.
Oh wait, you don't want that one, my bad!
Edit: I don't read so good
Registered: 1417566574 Posts: 4
Reply with quote #4
I use Matrix G27 grooved motor grip, works perfectly. the stock heat sink fits also.
Registered: 1420446753 Posts: 37
Reply with quote #5
I found a great one that makes it a breeze to put back in the motor and screw back in. It's the G&P Snake Skin type Long type motor. I tried the Umbrella Corp one but there isn't really any grip, so you may not like that one.
Registered: 1408205162 Posts: 36
Reply with quote #6
I just took the stock one off and used a dremmal to grind off the nub. Then I wrapped it with athletic tape to give it some grip. Looks good and way more comfortable.
Registered: 1420944503 Posts: 29
Reply with quote #7
Having issues blowing fuses when I swapped grips. Is this because there is too much pressure on the gear? Also is there a trick to getting the bottom plate on? Even the stock grip is giving me problems now.
Registered: 1420944503 Posts: 29
Reply with quote #8
Originally Posted by
snapshot Having issues blowing fuses when I swapped grips. Is this because there is too much pressure on the gear? Also is there a trick to getting the bottom plate on? Even the stock grip is giving me problems now.
Update: I happen to live very close to a reputable shop with a great gun tech. He had the grip on, motor running with no blown fuses in less than five minutes so I was causing the problem. He suggests a slightly thicker stock of metal on the motor electrical contacts. He suspects as I was adjusting the motor height the positive would slide off and arc or make contact with another part of the motor and cause the fuse to blow. After crimping the wire ends a little tighter, they held.
Registered: 1433751666 Posts: 9
Reply with quote #9
Has anyone tried the magpul moe grip? I used it on my kwa and I had to the bottom plate had to pop out of the bottom of the grip unevenly for the motor to be properly aligned. I've heard other people online having alignment issues as well and I was wondering if anyone has tries it on a trident series krytac because I ordered an spr and I hate the standard m4 grip.
KRISS Sierra Tango
Registered: 1407187299 Posts: 598
Reply with quote #10
I have installed the Magpul MOE/MIAD grip on our Trident series AEGs. The base plate does require slight modification in order for the alignment to be correct, but it does work.
Please note, any specifications given in my posts (unless specifically noted) are North America/US market specifications. Your specifications may differ due to different markets, your country's regulations, etc.
Registered: 1424126198 Posts: 5
Reply with quote #11
Where could I find the grip that comes on the new cerakote's?
__________________ Krytac CRB, Compact USP.
Registered: 1406759561 Posts: 846
Reply with quote #12
Those are from PTS, Ergo grip.
Registered: 1440302534 Posts: 15
Reply with quote #13
i have the g&p snakeskin grip, and it fits perfectly.
Registered: 1437964660 Posts: 17
Reply with quote #14
What kind of mods do you have to do to the moe grip to make it work? I got mine on but the motor kinda has an electrical smell to it after some shots and it feels like it's knocking against the side.
Registered: 1436453965 Posts: 13
Reply with quote #15
I just got my PTS MOE pistol grip in the mail today. I know that the base plate has to be modified for the motor to be properly aligned, but I'm a bit uneasy on doing it without knowing how it should end, and I don't trust the techs in my country. Could somebody who's done this (and it runs without issues or loose parts) post a picture of their modified MOE base plate, please?
__________________ No kill like overkill